A Step-by-Step Guide to Setting Up a Tub
A Step-by-Step Guide to Setting Up a Tub
Blog Article
Listed here in the next paragraph yow will discover a bunch of first-rate guidance involving Tools You Need to Install a New Bathtub .
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably tough task. If the old tub is readily easily accessible, the task can relocate speedily; if you have to open a wall to eliminate the old bathtub and place the new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub and set in the new one. Ensure you have certified on your own for the task and also fit trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is far better to consider using one prior to you begin. Possibilities are you may need an expert plumber to make tube connections.
This article will help you install a brand-new bath tub in your shower room if you have actually currently gotten a new tub and don't need to transform the plan of your previous supply of water pipes.
Your tools and also product list must make up the following:
Planning for the Installment
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather problematic because of the limited gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipes have actually been removed, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the needed setting. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bath tub till the level reads level.
To install taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the same for the other tap.
Switch on the supply of water as well as inspect all joints as well as new pipework for leaks as well as tighten them if needed. Fill up the tub as well as likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling as well as sealing around the tub ought to wait until the bathtub has actually been made use of at the very least when as this will certainly resolve it into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in location between the faucet and also the sink. Protect the tap in place with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous type needs to be linked to the tap finishes initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break a rigid seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, bring about issues with dampness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes as well as cartridges, and are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to allow for the motion experienced when the tub is in usage. The sealer can split fairly early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was introduced to that write-up about Installing A Bathtub from an acquaintance on another blog. Sharing is good. One never knows, you may very well be helping someone out. Thanks a lot for taking the time to read it.
Request Appointment
Report this page